- #Darkglass alpha omega full
- #Darkglass alpha omega free
You can use a regular mono instrument cable to connect the amplifier to the footswitch. The distortion push button will remain operational with the Intelligent Footswitch plugged in. You can also hold the footswitch to Mute the amplifier. This selection will define both the XLR and headphone out signal.įootswitch: The Intelligent Footswitch is a proprietary digitally controlled device that allows you to remotely engage and disengage the Alpha This input is routed only to the headphone output.Ĭabinet Select: Use this switch to navigate between the 3 different cabinet impulses or the clean DI signal. Headphone Output: Connect your Headphones and enjoy the impulse based cabinet emulation.ĪUX IN: Use this connector to play music from your laptop, phone, MP3 player, etc. USB: The USB connector allows you to use the Darkglass Suite to load different cabinet impulses or change different parameters on your amp. Both signals are available (Bypass and the amp signal with cabinet simulation) and are switched from the cab select switch. 
If you are experiencing ground noise in your DI signal try changing the setting of this control.ĭI Output: Use this connector to send your signal to the console, mic preamp, interface, etc. Ground Lift: Use this control to lift the ground of the DI XLR output. Master volume control is after this input. Return: Use this input to receive the signal from effects pedals. Send: Use this output to send the signal to effects pedals. Using an instrument cable can damage your amplifier. WARNING: Do not use an instrument cable with this jack. This Speakon combo jack allows for either Speakon or ¼” speaker cable operation.
Speaker Output: Use this connector to connect the amplifier to your cabinet. Mute: Use this push button to mute the amplifier. Master: Use this knob to control the overall volume of the amplifier. Use this slider to change the high content of the signal. These sliders control the mid content of the signal. Use this slider to change the low-end content of the signal. Mod: Selects or mixes between the two distinct distortion circuits: Alpha is punchy, tight with a lot of definition, whereas Omega is simply brutal and raw.īass: +-12dB at 80Hz.
Omega Engine’s output volume.īlend: Use this knob to mix between the Clean signal and the DIstortion signal (Alpha. It will change from a soft, warm overdrive to a massive and modern distortion sound. The compression can be turned off or assigned using the Darkglass Suite.ĭrive: This knob controls the amount of distortion that the Alpha The make up gain is adjusted automatically. Growl: Shelving Bass Boost for a fatter tone and increased low end saturation.Ĭompression: This knob controls the amount of dynamic compression added to the Alpha Omega Engine operates before the clean section (you can therefore use the 6-Band Active EQ for additional tone shaping).īite: Boosts high mids (2.8kHz) for additional presence and definition. 
Omega Engine™ to add natural compression, organic harmonic enhancement, and saturation ranging from mild overdrive to high gain bass rage. #Darkglass alpha omega free
If your bass is active it can have a hotter signal making the amp to distort early (feel free to use if such additional distortion is desired).ĭistortion: Use this push button to turn on or off the Alpha Passive/Active: Use this push-button switch to change from passive to active mode. Input: Use this jack to connect your instrument via a standard ¼” mono cable.
Omega 500 is a 500W amplifier equipped with an all-analog preamplifier, two distinct distortion circuits (Alpha and Omega), a custom-designed Darkglass high-efficiency class D Module, an ultra-quiet graphic equalizer, and a digital impulse-response cabinet emulator for DI outputs or headphones. 700VA Forced-air cooledĪC Input Power: 100-250 VAC (Via selector switch on left side panel).Ĭycles: 50/60 Hz Dimensions: 26.7cm l x 7cm h 25.5 w (10.5”l x 2.Do you want more photos? We are happy to provide them. Power Amp Input Level: 1500 mV RMS 1200MV RMS at 2Ωmode #Darkglass alpha omega full
Maximum Power Output: 900 Watts RMS 4Ω (1khz full blast 2 min max) 20%THD 450 Watts RMS 8Ω Minimum Load Impedance: 4Ω (2Ω in 2Ω mode) While Darkglass' signature Alpha and Omega drive engines add incredible girth and size to the overdriven signal, the studio-grade VCA compressor adds an extra layer of control, and the ultra-quiet 6-band graphic equalizer can help sculpt the tone from aggressive and overdriven to crystal clear clean, whatever your needs may be.
Omega 900 takes the best elements of their most successful distortion preamplifier ever, and combines it with state of the art features to make a monstrous 900-watt amplifier with earth-shattering tone. 
Darkglass Electronics Alpha Omega 900 Bass Amp
0 kommentar(er)
